GSO EN 17240:2025
EN 17240:2024
								
									
									Gulf Standard
								
								
								
									 
									Current Edition
									
								
								
									·
									Approved on
									14 October 2025
								
							
							Intelligent transport systems - ESafety - ECall end to end conformance testing for IMS packet switched based systems
GSO EN 17240:2025 Files
				                	 
				                    No files for this standard are available in the store currently.
				                
  
			                
			                
								
																								
												
													Obtaining this standard through the store is currently unavailable. You can acquire it directly from its source.
																								
											
										GSO EN 17240:2025 Scope
									This document defines the key actors in the eCall chain of service provision using IMS over packet switched networks (such as LTE/4G) as: 
1) In-vehicle system (3.20) (IVS)/vehicle, 
2) Mobile network Operator (MNO), 
3) Public safety answering point (3.27) (PSAP), 
and to provide conformance tests for actor groups 1) - 3). 
NOTE 1 Conformance tests are not appropriate nor required for vehicle occupants (3.36), although they are the recipient of the service. 
NOTE 2 Third party eCall systems (TPS eCall) are not within the scope of this deliverable. This is because the core TPS-eCall (3.32) standard (EN 16102) does not specify the communications link between the vehicle and the TPS service provider (3.29). 
NOTE 3 These conformance tests are based an the appropriate conformance tests from EN 16454 which was published before Internet Protocol multimedia Systems (IMS) packet switched networks were available. This deliverable therefore replicates the appropriate tests from EN 16454 (and acknowledge their source); adapt and revise Conformance Test Protocols (CTP) from EN 16454 to an IMS paradigm; or provide new additional tests that are required for the IMS paradigm. Some 14 112-eCall (Pan European eCall) tests provided in EN 16454 are specific to GSM/UMTS circuit switched communications and not appropriate for the IMS paradigm and are therefore excluded from this deliverable. 
This document therefore provides a suite of ALL conformance tests for IVS equipment, MNO's, and PSAPS, required to ensure and demonstrate compliance to CEN/TS 17184. 
NOTE 4 Because in the event of non-viability or non-existence of an IMS supporting network at any particular time/location, IMS-eCall systems revert to CS networked eCall systems eCall via GSM/UMTS, IVS and PSAPs need to support, and prove compliance to both IMS and CS switched networks. 
The Scope covers conformance testing (and approval) of new engineering developments, products and systems, and does not imply testing associated with individual installations in vehicles or locations.
									
								
							
						
					Best Sellers From Mechanical Sector
OS GSO 42:2015
   
                        
                            GSO 42:2015 
                        
                        
                    
                            
                            
                                Omani Standard
                            
                        
                        
                            
                            
                                
                                MOTOR VEHICLES - GENERAL REQUIREMENTS
                            
                        
                        
                         
                                
                            
                                
                                     
                                
                            
                        GSO 42:2015
   
                        
                            
                            
                                Gulf Technical Regulation
                            
                        
                        
                            
                            
                                
                                MOTOR VEHICLES - GENERAL REQUIREMENTS
                            
                        
                        
                         
                                
                            
                        GSO 159:1993
   
                        
                            
                            
                                Gulf Technical Regulation
                            
                        
                        
                            
                            
                                
                                MOTOR VEHICLES –
DIMENSIONS AND WEIGHTS
                            
                        
                        
                         
                                
                            
                        OS GSO 159:1993
   
                        
                            GSO 159:1993 
                        
                        
                    
                            
                            
                                Omani Standard
                            
                        
                        
                            
                            
                                
                                MOTOR VEHICLES –
DIMENSIONS AND WEIGHTS
                            
                        
                        
                         
                                
                            
                                
                                     
                                
                            
                        Recently Published from Mechanical Sector
OS GSO 170:1994
   
                        
                            GSO 170:1994 
                        
                        
                    
                            
                            
                                Omani Standard
                            
                        
                        
                            
                            
                                
                                METHODS OF TEST FOR GAS FIRED
DOMESTIC RADIANT TYPE 
PORTABLE HEATERS
                            
                        
                        
                         
                                
                            
                                
                                     
                                
                            
                        GSO 1796:2007
   
                        
                            
                            
                                Gulf Standard
                            
                        
                        
                            
                            
                                
                                Methods of test for two pieces aluminum round cans used for canning food (Beverages & stuffs
                            
                        
                        
                         
                                
                            
                        GSO 230:2005
   
                        
                            
                            
                                Gulf Standard
                            
                        
                        
                            
                            
                                
                                MOTOR VEHICLES —
BRAKE FLUID – SIMULATED SERVICE
PERFORMANCE TEST
                            
                        
                        
                         
                                
                            
                        OS GSO ISO 4548-3:2002
   
                        
                            ISO 4548-3:1997 
                        
                        
                    
                            
                            
                                Omani Standard
                            
                        
                        
                            
                            
                                
                                METHODS OF TEST FOR FULL-FLOW
LUBRICATING OIL FILTERS FOR INTERNAL 
COMBUSTION ENGINES - PART 3:  RESISTANCE
TO HIGH DIFFERENTIAL PRESSURE AND TO 
ELEVATED TEMPERATURE
                            
                        
                        
                         
                                
                            
                                
                                     
                                
                            
                                
                                    