GSO CEN/TR 13932:2023
Gulf Standard
Current Edition
·
Approved on
28 February 2023
·
Rotodynamic pumps - Recommendations for fitting of inlet and outlet on piping
GSO CEN/TR 13932:2023 Files
No files are available for this standard right now!
GSO CEN/TR 13932:2023 Scope
This CEN Technical Report lays down stipulations relating to installation conditions for sudden change in section or direction (elbows, tee fittings, junctions) and the most widely used accessories at the inlet and outlet of pumps (valves and fittings) in order to minimise the effect of disturbances in the flow of liquid thereby created upstream and downstream from the pump and on the operation of the pump.
NOTE 1 The recommendations given in this document permit to solve a majority of the most current cases.
These recommendations relate to three aspects of installation:
the fitting of the pump to pipework by convergent and divergent pipes;
in the case of elbows, tees and branching, their direction with respect to the axis of the pump;
the minimum clearances to be adhered to between a disturbing (elbow, valve, etc.) and the mounting flange of the pump.
This document applies to the installation of rot dynamic pumps (centrifugal, mixed flow and axial flow) fitted in piping. It applies to pumps having intake diameters equal to or less than 500 mm. The recommendations may be adapted in agreement with the pump manufacturer for intakes having dimensions exceeding 500 mm or for special applications. This document is not applicable to pumps of which the inlet is located in reservoirs, sumps or tanks and which will be dealt with in a subsequent standard.
The recommendations in this document are only valid under the following conditions:
Newtonian fluids having a maximum viscosity of 2.10-4 m2/s;
occluded gas content at pumping temperature and inlet pressure not exceeding 2 % by volume for water and
4 % for other fluids;
solids content (small particle size, such as sand) not exceeding 1 % by volume, nor 1 % by weight;
in piping with diameters D1 and D2 (see Figure 11), flow rate velocity, should be in the following ranges:
3 m/s to 5 m/s at inlet;
4 m/s to 10 m/s at outlet.
Best Sellers From Mechanical Sector
OS GSO 42:2015
GSO 42:2015
Omani Standard
MOTOR VEHICLES - GENERAL REQUIREMENTS
![OS Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_os_sml.png)
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 42:2015
Gulf Technical Regulation
MOTOR VEHICLES - GENERAL REQUIREMENTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
GSO 159:1993
Gulf Technical Regulation
MOTOR VEHICLES –
DIMENSIONS AND WEIGHTS
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
OS GSO 159:1993
GSO 159:1993
Omani Standard
MOTOR VEHICLES –
DIMENSIONS AND WEIGHTS
![OS Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_os_sml.png)
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
Recently Published from Mechanical Sector
GSO ISO 21384-2:2024
ISO 21384-2:2021
Gulf Standard
Unmanned aircraft systems — Part 2: UAS components
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)
GSO ISO 22407:2024
ISO 22407:2021
Gulf Standard
Metallic materials — Fatigue testing — Axial plane bending method
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)
GSO ISO 24513:2024
ISO 24513:2019
Gulf Standard
Service activities relating to drinking water supply, wastewater and stormwater systems — Vocabulary
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)
![ISO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_iso_sml.png)
GSO EN 14622:2024
EN 14622:2005
Gulf Standard
Devices to prevent pollution by backflow of potable water - Air gap with circular overflow (restricted) - Family A, type F
![GSO Standard](https://static.gso.org.sa/gso-uicore/assets/images/logo_gso_sml.png)