GSO ISO 19085-9:2022

Gulf Standard   Current Edition
Approved on  12 May 2022

Woodworking machines — Safety — Part 9: Circular saw benches (with and without sliding table)

GSO ISO 19085-9:2022 Files

GSO ISO 19085-9:2022 Scope

This document gives the safety requirements and measures for stationary and displaceable circular saw benches (with or without sliding table and/or demountable power feed unit), also known as "table saws" (in the USA), hereinafter referred to as "machines", designed to cut wood and material with similar physical characteristics to wood.

NOTE 1 For the definition of stationary and displaceable machine, see ISO 19085‑1:2017, 3.4 and 3.5.

It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to these machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account.

NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.

It is also applicable to machines fitted with one or more of the following devices, or working unit, whose hazards have been dealt with:

— device for the main saw blade and scoring saw blade to be raised and lowered through the table;

— device to tilt the main saw blade and scoring saw blade for angled cutting;

— device for scoring;

— device for grooving with milling tool with a width not exceeding 20 mm in one pass;

— demountable power feed unit;

— additional manually operated sliding table;

— powered work-piece clamping device.

NOTE 3 Circular saw benches are used for ripping, cross cutting, dimensioning and grooving.

This document does not apply to:

a) transportable/displaceable machines intended for outdoor use on building sites;

NOTE 4 Building site saws (contractor saws) are covered by the requirements of ISO 19085‑10:2018.

b) hand held woodworking machines including any adaptation permitting their use in a different mode, i.e. bench mounting;

c) machines intended for use in a potentially explosive atmosphere;

d) machines manufactured before the date of its publication as an International Standard;

e) transportable machines with a maximum saw blade diameter of ≤315 mm.

NOTE 5 Transportable motor-operated electric tools are dealt with in IEC 62841‑1:2014 and IEC 62841‑3‑1:2014.

Best Sellers From Mechanical Sector

OS GSO 42:2015
GSO 42:2015 
Omani Standard
MOTOR VEHICLES - GENERAL REQUIREMENTS
GSO 42:2015
 
Gulf Technical Regulation
MOTOR VEHICLES - GENERAL REQUIREMENTS
GSO 159:1993
 
Gulf Technical Regulation
MOTOR VEHICLES – DIMENSIONS AND WEIGHTS
OS GSO 159:1993
GSO 159:1993 
Omani Standard
MOTOR VEHICLES – DIMENSIONS AND WEIGHTS

Recently Published from Mechanical Sector

GSO EN 17038-1:2023
EN 17038-1:2019 
Gulf Standard
Pumps - Methods of qualification and verification of the Energy Efficiency Index for rotodynamic pump units - Part 1: General requirements and procedures for testing and calculation of Energy Efficiency Index (EEI)
GSO EN 14452:2023
EN 14452:2005 
Gulf Standard
Devices to prevent pollution by backflow of potable water - Pipe interrupter with atmospheric vent and moving element DN 10 to DN 20 - Family D, type B
GSO ISO 11298-4:2023
ISO 11298-4:2021 
Gulf Standard
Plastics piping systems for renovation of underground water supply networks — Part 4: Lining with cured-in-place pipes
GSO ISO 24528:2023
ISO 24528:2021 
Gulf Standard
Service activities relating to drinking water supply, wastewater and stormwater systems — Guideline for a water loss investigation of drinking water distribution networks