GSO ISO 14577-4:2014

ISO 14577-4:2007
Gulf Standard   Current Edition · Approved on 25 December 2014

Metallic materials -- Instrumented indentation test for hardness and materials parameters -- Part 4: Test method for metallic and non-metallic coatings

GSO ISO 14577-4:2014 Files

English 24 Pages
Current Edition Reference Language
OMR 30.71

GSO ISO 14577-4:2014 Scope

This part of ISO 14577 specifies a method for testing coatings which is particularly suitable for testing in the nano/micro range applicable to thin coatings. This test method is limited to the examination of single layers when the indentation is carried out normal to the test piece surface, but graded and multilayer coatings can also be measured in cross-section if the thickness of the individual layers or gradations is greater than the spatial resolution of the indentation process. The test method is not limited to any particular type of material. Metallic, non-metallic and organic coatings are included in the scope of this part of ISO 14577. The application of this part of ISO 14577 regarding measurement of hardness is only possible if the indenter is a pyramid or a cone with a radius of tip curvature small enough for plastic deformation to occur within the coating. The hardness of visco-elastic materials, or materials exhibiting significant creep will be strongly affected by the time taken to perform the test. NOTE 1 ISO 14577-1, ISO 14577-2 and ISO 14577-3 define usage of instrumented indentation testing of bulk materials over all force and displacement ranges. NOTE 2 The application of the method of this part of ISO 14577 is not needed if the indentation depth is so small that in any possible case a substrate influence can be neglected and the coating can be considered as a bulk material. Limits for such cases are given. NOTE 3 The analysis used here does not make any allowances for pile-up or sink-in of indents. Use of Atomic Force Microscopy (AFM) to assess the indent shape allows the determination of possible pile-up or sink-in of the surface around the indent. These surface effects result in an under-estimate (pile-up) or over-estimate (sink-in) of the contact area in the analysis and hence may influence the measured results. Pile-up generally occurs for fully work-hardened materials. Pile-up of soft, ductile materials is more likely for thinner coatings due to the constraint of the stresses in the zone of plastic deformation in the coating. It has been reported that the piled up material results in an effective increase of the contact area for the determination of hardness, while the effect is less pronounced for the determination of indentation modulus, since the piled up material behaves less rig.

Best Sellers From Mechanical Sector

GSO 42:2015
 
Gulf Technical Regulation
MOTOR VEHICLES - GENERAL REQUIREMENTS
GSO 98:1988
 
Gulf Technical Regulation
MOTOR VEHICLES- FLAMMABILITY OF INTERIOR MATERIALS AND THEIR TESTING METHODS
GSO 159:1993
 
Gulf Technical Regulation
MOTOR VEHICLES – DIMENSIONS AND WEIGHTS
GSO 1780:2010
 
Gulf Technical Regulation
Motor vehicle-vehicle identification number (vin) - requirements

Recently Published from Mechanical Sector

OS GSO EN 131-3:2018+A1:2026
EN 131-3:2018+A1:2025 
Omani Standard
Ladders - Part 3: Marking and user instructions
OS GSO EN 10217-1:2026
EN 10217-1:2019 
Omani Standard
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 1: Electric welded and submerged arc welded non-alloy steel tubes with specified room temperature properties
OS GSO EN 17860-1:2026
EN 17860-1:2024 
Omani Standard
Carrier cycles - Part 1: Terms and definitions
OS GSO ASTM A182/A182M:2026
ASTM A182/A182M:26a 
Omani Standard
Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service